3DVIA Composer Intro Video

by adminwp on June 18, 2009 · 0 Comments

 This is a large, 5 minute video. Content will begin loading automatically but will take a few minutes to load completely…  Click pause and play when ready. {wmv}3DVIA_Composer_800x600|800|620{/wmv}

Continue Reading →

Product Videos

by adminwp on June 18, 2009 · 0 Comments

Product Videos SolidWorks Enterprise PDM 2D Legacy Data Tools

Continue Reading →

SolidWorks 2D Legacy Tools Video

by adminwp on May 20, 2009 · 0 Comments

 Content may take a few moments to load… {flv}2D-legacy-tools|800|600{/flv}

Continue Reading →

SolidWorks Enterprise PDM Demo Video

by adminwp on May 20, 2009 · 0 Comments

 Content may take a few moments to load… {swf}Enterprise-PDM-Demo|800|600{/swf}

Continue Reading →

Tim’s Homepage

by adminwp on May 20, 2009 · 0 Comments

Webinar Videos SolidWorks Enterprise PDM 2D Legacy Data Tools

Continue Reading →

SolidWorks Simulation Premium 2010 Dynamics

by adminwp on May 19, 2009 · 0 Comments

Prerequisites: SolidWorks Simulation – Students must have attended the introductory SolidWorks Simulation course or must have working knowledge of the SolidWorks Simulation software. knowledge of basic principles in Vibrations is strongly recommended, but not required. Knowledge of SolidWorks and basic mechanical engineering concepts is recommended. Description: This course is targeted for the users who would [...]

Continue Reading →

SolidWorks Simulation Premium 2010 Nonlinear

by adminwp on May 19, 2009 · 0 Comments

Prerequisites: SolidWorks Simulation – Students must have attended the introductory SolidWorks Simulation course or must have working knowledge of the SolidWorks Simulation software. Knowledge of SolidWorks and basic mechanical engineering concepts is recommended. Description: This class will raise your SolidWorks Simulation FEA skills to the next level! It offers hands-on experience on the use of [...]

Continue Reading →

SolidWorks Simulation Premium 2010 Dynamics Curriculum

by adminwp on May 19, 2009 · 0 Comments

  Lesson 1: Analyses Covered Modal time history analysis Steady-state harmonic analysis Random vibration Lesson 2: Damping Rayleigh damping, modal damping, composite damping Lesson 3: Excitation  Load vs. time data for nodal forces, pressure loads Uniform and non-uniform base excitations in the time or frequency domain for displacement, velocity and acceleration Harmonic excitation for nodal forces, [...]

Continue Reading →

SolidWorks Simulation Premium 2010 Nonlinear Curriculum

by adminwp on May 19, 2009 · 0 Comments

  Lesson 1: Geometric NonlinearitiesLarge displacements problemsLarge strain formulation Lesson 2: Material NonlinearitiesNonlinear elasticityHyperelasticity (Mooney-Rivlin, Ogden)Plasticity (von Mises, isotropic/kinematic/mixed hardening rules)Temperature dependent material propertiesVisco-elasticity and creep Lesson 3: Contact (Boundary) Nonlinearities3D nonlinear gap/contact analysis (with or without material nonlinearities) Lesson 4: Numerical ProceduresSolution control techniques (force, displacement, and Arc-Length controls)Equilibrium Iterations schemes (Newton-Raphson, modified Newton-Raphson)Termination [...]

Continue Reading →

SolidWorks Weldments Hot Fix

by adminwp on May 16, 2009 · 0 Comments

Weldments Hot Fix There is a hotfix for SP4 that addresses trims between groups inweldments with S-039538 and SPR 505508. See below. S-039538 When opening a Weldment part in SolidWorks 2009 SP4.0,why does the automatic trim/extend between Groups in a structural member fail? A problem was identified in SolidWorks 2009 SP4.0 that did not exist [...]

Continue Reading →